[Isocops] IBEX Orbit #503 ATS Approval ( 4 Oct 20 13 Oct 20)

[Nigel Angold]

I approve IBEX_2020_278_o0503a_BUS_v002.scr for uplink during today's apogee contact.

I approve IBEX_2020_278_o0503a_INST_v001.scr for uplink when there’s space to store the 46 commands onboard. Today too?

Two orbit 503 INST commands (Science State and Lo Science Mode Normal ) overlap with orbit 502 BUS (Tx commands) commands. But that’s ok. 

Thanks,
Nigel

> All,
>    Attached are the planning files for Orbit #503
> Please respond to this thread with comments and approvals.  
> Approvals are required by COB on 19 September 2020
>  
> Please note the following:
> I generated 3 separate ATS files BUS, INST and a complete file. The BUS and INST will be the files to be uplinked. The complete ATS, I used as a sanity check to see how the commands lined up. Since we are in a new phase of ATS generation. IF you have any ideas of doing this differently, let me know.
>  
> The 3 ATS files have been changed to word  files and encrypted. I will send out another email with the password. The files that have been transferred via MFT have not been encrypted and are still text files.  
>  
> I moved the 2 House Keeping commands from the INST ATS to the BUS ATS. I commented out the 2 commands in the INST ATS. If for some reason we were unable to uplink the INST Commands for this orbit, we would have been in the wrong spacecraft state for executing the maneuver commands. 
>  
> Battery Balancing this orbit
> # 2020-10-13T12:27:12.723Z,Perigee,orbit:503
> Begin - 2020/10:13:12:00:00 – End - 2020/10:13:13:30:00
>  
> 5.       Orbit# 501 Reset Master Timer  - 2020/09:25:13:15:00
>  
> APL Contact
> The commands have been commented out because I am still waiting on the schedule confirmation from APL. I will create a separate ATS for the APL contact once the contact has been confirmed.
> Just a reminder for the APL contact. We will start off at 2k D\L, after 5 minutes we switch to 320k D\L. Then 5 minutes later we start the SSR Dump With Dump New command
>  
> 7.       Command Load Constraint Violation Report (CCVR)
> 
> IBEX_2020_278_o0503a_v001.ccvr
> # Input files:         1
> #   IBEX_2020_278_o0503a_v001.scr
>  
> ==========================
> HARD CONSTRAINT VIOLATIONS
> ==========================
> NO VIOLATIONS.
>  
> ==========================
> SOFT CONSTRAINT VIOLATIONS
> ==========================
> IBX-CLC-016: No command to enable spin pulse protection was found after
>              transition to science mode at 2020/10/04 05:36:29 UTC
> IBX-CLC-016: No command to enable spin pulse protection was found after
>              transition to science mode at 2020/10/08 12:12:32 UTC
>  
> ==============
> OTHER MESSAGES
> ==============
> NO MESSAGES.
>  
> Timothy E.Perry
> CRS IBEX OCO-2
> Mission Operations
> timothy.perry at ngc.com <mailto:timothy.perry at ngc.com>
> Office (703) 406-5976
> Cell (301) 606-1430
>  
> <image001.png>
>  
>  
> <IBEX-Command-Approval-Checklist-Rev16_F_503_TEP.docx><IBEX_Orbit503_Contacts.txt><IBEX_2020_278_o0503a_v001.ccvr><IBEX_2020_278_o0503a_BUS_v001.ccvr><IBEX_2020_278_o0503a_INST_v001.ccvr><IBEX_2020_278_o0503a_INST_v001.oef><IBEX_2020_278_o0503a_BUS_v001.oef><IBEX_2020_278_o0503a_INST_v001.docx><IBEX_2020_278_o0503a_BUS_v001.docx><IBEX_2020_278_o0503a_v001.docx>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.sr.unh.edu/pipermail/isocops/attachments/20200919/7285ced1/attachment-0002.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: IBEX-Command-Approval-Checklist-Rev16g-o503-nga.ngpdf
Type: application/octet-stream
Size: 163745 bytes
Desc: not available
URL: <https://lists.sr.unh.edu/pipermail/isocops/attachments/20200919/7285ced1/IBEX-Command-Approval-Checklist-Rev16g-o503-nga-0001.ngpdf>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.sr.unh.edu/pipermail/isocops/attachments/20200919/7285ced1/attachment-0003.html>